KVH Industries TracPhone FB150 User Manual Download

Page: 125 / 140

Chapter 5: Troubleshooting

Status signaling

116

08031

Failed to enter

normal

operation

Antenna failed to start up

normally.

Reboot the terminal.
Contact your dealer/

distributor if the problem

persists.

08032

Firmware image

version lower

than active

antenna version

The firmware in the

antenna is newer than

expected by the terminal.

Update the terminal

software.

08033

Firmware image

doesn't support

antenna

hardware

The antenna hardware

version is not supported

by the terminal.

Check that both the

antenna and the terminal

are of the type

TracPhone FB150.
Contact your dealer/

distributor if the problem

persists.

08034

Antenna failed

to exit Flash

Manager. Power

cycle needed

New firmware was

successfully uploaded to

the antenna but the

antenna failed to start

normally with the new

firmware.

Reboot the terminal.

Contact your dealer/

distributor if the problem

persists.

08035

Unable to open

port for HPA

burst

monitoring

There was an error

communicating with the

antenna.

Reboot the terminal.

Contact your dealer/

distributor if the problem

persists.

08036

Radio silence

is activated

The Radio silence function

is activated. No

transmission is allowed.

If the Radio silence

function should not be

active, enter the web

interface and select

SETTINGS > Discrete

I/O

. Then clear the

Enabled

box for

Radio

silence

08045

Antenna -

Startup

temperature too

low

The temperature in the

antenna is too low for the

system to start up.

None. If the ambient

temperature is outside the

specified limits, the

antenna may not be able to

start up properly. Refer to

the installation manual for

temperature specifications.

Event Text

Explanation

Remedy

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands