KVH Industries TracPhone FB150 User Manual Download

Page: 127 / 140

Chapter 5: Troubleshooting

Status signaling

118

08054

Transmission

aborted due to

extreme

temperature

The system stops all

transmission due to:
• critically high

temperature in the

HPA or ACM module

of the antenna, or

• too low temperature in

the ACM module.

None.
The antenna must operate

within the allowed

temperature range to work

properly. For information

on ambient temperature

limits, see the installation

manual.

08056

USIM rejected

The type of USIM card

inserted in the terminal is

not correct for your

terminal.

Make sure you have the

correct type of USIM card

(a USIM card for a land-

mobile system will not

work for a maritime

system and vice versa).

0912A

Motor stopped

The motors in the antenna

have stopped because the

temperature is critically

high or critically low.

When the temperature is

normalized the motors

automatically start up

again.

Event Text

Explanation

Remedy

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands