KVH Industries TracPhone FB150 User Manual Download

Page: 29 / 140

Chapter 2: Getting started

Standard connection to the Internet (default)

Activating the connection using the IP handset

To activate the connection using the IP handset, do as follows:

1. Connect the IP handset to one of the LAN ports (preferably port 1).

The handset starts up automatically.

2. Select

Menu > BGAN

in the handset.

3. Select

Connect

4. Use the left/right keys to find the network user group for the application you

want to start.

5. Press

Start

to start the connection.

A confirmation window is displayed.

6. Press

Yes

to continue.

The IP handset sends a command to the terminal to start the selected connection.

7. Check the connection e.g. by entering a web site from a connected computer.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands