KVH Industries TracPhone FB150 User Manual Download

Page: 96 / 140

Chapter 4: Using the web interface

Uploading software

Uploading software from your computer

To upload software from your computer to the terminal, do as follows:

1. Download the new software as described in the next section, or acquire the

software from KVH Industries and save it on your computer.

2. Open the web interface and do one of the following:

• If the PIN has been accepted (or a PIN is not required), select

SETTINGS >

Upload

from the left navigation pane.

• If a PIN is required and the PIN has not been entered, select

ADMINISTRATION

, enter the Administration PIN and password and click

Logon

The default user name is

admin

and the default password is

1234

Then select

Upload

from the left navigation pane.

The UPLOAD page opens.

3. In the field

UPLOAD SOFTWARE TO TERMINAL

, click

Browse...

4. Browse to the new software version and accept it.

5. Click the

Upload

button.

Note that the upload procedure takes a couple of minutes.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands