Kval 990-HQ Operation Manual Download Page 52

Page: 52 / 92

Powering Operations for the 990-HQ

2-24

990-HQ Operation Manual

Powering Operations for the 990-HQ

This section describe how to power up and to power down the

990-HQ

Applying power to the entire system

• Starting the Control Circuit

Powering down the system includes:

• Shutting down the control power
• Removing power from the entire system

How to Power Up the 990-HQ

Ensure factory air is applied to machine and main air supply is turned on.

Make sure all E-Stop buttons are out.

Note:

The E-Stop Indicator Button on the main screen will alert the operator if an E-

Stop is activated.

Make sure the electrical disconnect the electrical cabinet is turned to the ON posi-

tion.

Move the Feeder,

990-HQ

, and the feeder C

ONTROL

CIRCUIT

switches to the ON position. they all should

light up.

Note:

Boot up may take 2 to 3 minutes.

Note:

Refer to the Feeder/Stacker manual for informa-

tion specific about these machines

Push all the green

START MACHINE b

uttons.

Wait for the machine feedback on the operator

screen displays “

Ready to Home

”.

All lights on the status light panel on the electrical

box should be illuminated.

See “Description of

the Six Light Panel” on page 2-20

Summary of Contents for 990-HQ





























































































Search results

Summary of Contents for 990-HQ

Reviews:

Related manuals for 990-HQ

Brands by name

Popular brands

Kval 990-HQ, Operation Manual

Search results

Summary of Contents for 990-HQ

Reviews:

Related manuals for 990-HQ

Brands by name

Popular brands