manualshive.com logo in svg

Kval 990-HQ, Operation Manual

Share
Download
Kval 990-HQ Operation Manual Download Page 39

Screw Track-
ing Plate 
Assembly

Gate Assembly

Hopper

 

Hopper Cylinder

Screw Delivery Tubes Air Injected 
(Not Shown)

Screw Pick 
Off Slide 
Assembly

Screw Pick-Off 
Cylinder (Door)

Screw Pick-Off 
Cylinder (Jamb)

Note: 

The Screw Pick-Offs 

has the ability to deliver 
screws to the Jamb or 
Door separately or both 
as well as both at the 
same time

   About the Eight Shooter System

2-11

990-HQ Operation Manual

FIGURE 3. 

Hopper Part Call-Outs

Hopper Process

1. 

Pour the Screws into the 

Hopper.

2. 

The recommended maximum amount of screws a quantity of 600.

3. 

The

 Hopper

 moves up and down periodically during the process by the 

Hopper Cyl-

inders 

to organize the screws and deliver them to the 

Screw Tracking Plate

.

4. 

The 

Gate Assembly 

monitors the quantity of screws delivered to the to the 

Screw 

Tracking Plate Assembly.

Summary of Contents for 990-HQ





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands