Küenle KFU 2 Series Manual Download Page 125

Page: 125 / 254

KFU 2-/4-

124

The behavior of the positioning after the required position of the drive is reached can
be defined via the

Activity after positioning

463

parameter.

Activity after positioning

463

Function

0 -

End positioning

The drive is stopped with the stopping behavior
of

Operation mode

630

1 -

Wait for positioning signal

The drive is stopped until the next signal edge;

with a new edge of the position signal, it is ac-

celerated in the previous direction of rotation.

2 -

Reversal

by new edge

The drive is held until the next signal edge; with

a new edge of the position signal, it is acceler-

ated in the opposite direction of rotation.

3 -

Positioning; off

The drive is stopped and the power output stage

of the inverter is switched off.

4 -

Start by time control

The drive is stopped for the

Waiting time

464

;

after the waiting time, it is accelerated in the

previous direction of rotation.

5 -

Reversal by time control

The drive is held for the

Waiting time

464

; after

the waiting time, it is accelerated in the opposite

direction of rotation.

The position reached can be maintained for the

Waiting time

464

, then the drive is

accelerated according to operation mode 4 or 5.

Parameter

Settings

No.

Description

Min.

Max.

Fact. sett.

464 Waiting time

0 ms

3600,000 ms

0 ms

Positioning, Operation Mode 458 = 1

The diagram shows how the positioning to the set positioning distance is affected.
The positioning distance remains constant at different frequency values. At the refer-
ence point, the position signal S

Posi

is generated. Starting from frequency f

max

, the

positioning is affected at the set

Deceleration (clockwise)

421

. At a lower frequency

value f

, the frequency remains constant for some time before the drive is stopped at

the set deceleration.
If, during acceleration or deceleration of the machine, positioning is started by the
signal S

Posi

, the frequency at the time of the positioning signal is maintained.

m ax

pos i

m i n

Digital Input

Deceleration (Clockwise)

421

Summary of Contents for KFU 2 Series































































































































































































































































Search results

Summary of Contents for KFU 2 Series

Reviews:

Brands by name

Popular brands

Küenle KFU 2 Series, Manual

Search results

Summary of Contents for KFU 2 Series

Reviews:

Brands by name

Popular brands