FRONT AXLE
RTV1140CPX, WSM
5-S12
(Continued)
(When reassembling)
• When installing the strut (1) to knuckle case assembly (12), set
the wedge to decide the position of strut to the slit of the knuckle
case assembly.
• When inserting the cotter pin, if the slots in the nut do not align
with the cotter pin hole in the tie-rod end or knuckle case
mounting bolt, tighten the nut clockwise up to next alignment. It
should be within 30 degree.
• Loosen once and tighten again, when the slit goes past the
nearest hole.
• After tightening the these slotted nut to the specified tightening
torque, install a cotter pin as shown in the figure.
• Apply anti-fretting grease (NISSEKI PYRONOC UNIVERSAL
N6C or its equivalents) to spline of propeller shaft (14) and
pinion shaft.
NOTE
• Tighten the lower arm mounting bolt and nut (3) with the
specified tightening torque after setting up the wheel and
unloading the machine on ground.
9Y1210293FAS0012US0
Tightening torque
Tie-rod end slotted nut
50 N·m
5.1 kgf·m
37 lbf·ft
Ball joint mounting screw
and nut
48.0 to 55.9 N·m
4.90 to 5.70 kgf·m
35.4 to 41.2 lbf·ft
Knuckle case mounting bolt
and slotted nut
48.0 to 55.9 N·m
4.90 to 5.70 kgf·m
35.4 to 41.2 lbf·ft
Front differential case
mounting nut
36.0 to 40.0 N·m
3.07 to 4.07 kgf·m
26.6 to 29.5 lbf·ft
(1) Strut
(12) Knuckle Case Assembly
(14) Propeller Shaft
(17) Front Differential Assembly
(18) Front Differential Case Mounting
Nut
(19) Slit
KiSC issued 05, 2014 A
Summary of Contents for RTV1140CPX
