OPERATION
H325 IAE
Rev.: 004
kortho
QiC i-series
8-21
Fig. 8.31
Print head resistance
Pre-heater
This setting should be used to switch the pre-heat function on or off. The preheat function is used to regulate
the temperature of the printhead to ensure optimum print quality. It is recommended that the Pre-heater
setting be set to
Yes
when the temperature inside the building, in which the printer is used, is below 20°C or
when the substrate is hard to print on. When
Yes
is selected a green LED will light on the control unit when
power is supplied to the heating element. Set the temperature using the
Temperature
setting.
Temperature
See Pre-heater above. Depending on the print quality the value must be adjusted to the optimal value. The
range is 25
°
C to 45
°
C. Refer to section 7.3.
Push home
It is only necessary for this value to be set when the printer is mounted vertically printing downwards. Due
to vibrations there is a chance that the printhead will slowly move downwards (out of its home position) at
that time.
When this function is activated, the print head carriage is pushed back into the home position before each
print. One can set the time the carriage is pushed back in milliseconds. Generally this variable will be set by
the service engineer when the printer is installed. The setting range is 0 to 550ms, when set to 0 the function
is de-activated.
Note:
Using this option will decrease the number of prints per minute (PPM) because it takes time to
push the printhead carriage back into the home position. Once the carriage is pushed back for the
set amount of milliseconds, the system will make the print.
Pinter ID
This is a number from 0-255 that can be used to identify the printer. The printer ID can be used in the label
design and can in this way be printed on the substrate.
8.6.3 Signal settings
To change the signal settings touch the
Signal
button.
CAUTION:
These settings will be set during installation; only a trained engineer should change them.
i
Summary of Contents for qic i series
