Kioti CS2610 Manual Download Page 86

Page: 86 / 170

cS2610

1. Adjust the seat and fasten the seat

belt.

M46O504A

(1) Seat

(2) Seat Adjustment lever (Sliding)

6. Start the engine of the tractor

with the charged battery.

7. Start the engine of the tractor

with the discharged battery.

8. Disconnect the black cable from

the negative battery terminals of

both of the tractors.

9. Disconnect the red cable.
10. Run the engine for at least 30

minutes to charge the discharged

battery.

11. If the battery is discharged again,

replace it or check the charging

system, such as the alternator.

OPERATING.THE.TRACTOR

DRIvING



Check.if.the.seat.is.securely.

locked.after.the.seat.adjustment.



Do.not.adjust.the.seat.while.

driving..The.seat.may.move.

suddenly.causing.the.loss.of.

control.of.the.tractor.

WARNING

1. check that the voltage of the dis-

charged battery is same as the

voltage of the other tractor or ve-

hicle for jump start. (Specification

for this tractor: 12v)

2. check the length of the jump cable

and position another tractor near

the tractor with the discharged bat-

tery. Then, put all the shift levers in

the neutral position, apply the park-

ing brake, and stop the engine.

3. Wear protective glasses and gloves

and open the hoods of both trac-

tors. Remove the battery terminal

cover as necessary.

4. connect the alligator clips on both

ends of the red positive cable to the

positive terminals of both batteries.

5. connect one clip of the black nega-

tive cable to the negative terminal

of the normal battery and the other

clip to the tractor body with the dis-

charged battery. make sure to con-

nect the clip to a part of the frame

without paint.

M46-EU,AU-05.indd 10

2012-01-18 오후 6:38:22

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands