Kioti CS2610 Manual Download Page 150

Page: 150 / 170

cs2610



Never use a fuse with the ca-

pacity higher than specified

on the fuse box cover.



If using a faulty fuse, steel

wire, or foil, the electrical de-

vice can be damaged or even

can catch a fire.

WARNING



If the replaced fuse blow, it is

probable that the wiring sys

tem is faulty. In this case, con-

tact your local kIOTI Dealer.



If the fusible link, relay or

other electrical component is

faulty, contact your local kIOTI

Dealer.

NOTE

(1) slow Blow fuse

M46O738A

slOW BlOW fUsE (AP)

slow blow fuse

40 A



Using a non-approved slow-

blow fuse can damage electrical

systems in the tractor severely.



Refer to the chapter "Trouble

shooting" in this manual or

contact your local kIOTI Dealer

for specific information dealing

with electrical problems.

IMPORTANT

the slow blow fuse is to protect the

electric wiring. If it is blown, find and

repair the cause and replace it with a

new genuine

kIOTI

part.

M46-EU,AU-07.indd 32

2012-01-18 오후 6:40:03

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands