Kioti CS2610 Manual Download Page 142

Page: 142 / 170

cs2610

M46O728A

(1) Battery

(2) sight glass

BATTERy INsPECTION

check the battery sight glass fre-

quently to keep the battery in the

best condition.

Blue: Battery normally charged
Black: Battery discharged, im-

mediate charge required

white: Battery replacement required

1. while charging the battery, steam

is generated from water in the elec-

trolyte. if the amount of electrolyte

is insufficient, the battery can be

damaged. on the other hand, if the

amount of electrolyte is excessive,

the tractor can be damaged. there-

fore, special care should be taken

for the amount of electrolyte.

2. to slow charge the battery, connect

the battery positive terminal to the

charger positive terminal and the

negative to the negative, and then

recharge in the standard fashion.

3. Boost charging is only for emer-

gencies. it will partially charge the

battery at a high rate and in a short

time. failure to do this will shorten

the battery’s service life.

4. when the battery is discharged

and should be replaced, replace it

with a new one with same specifi

cation and capacity.

ChARGING

Battery type

Volts (v)

55ah



The charge warning lamp

comes on if the charging sys-

tem is defective. If it comes on

while driving, have the system

checked or repaired by your

local kIOTI Dealer.



Keep the battery fully charged.

If the battery fluid concentra-

tion is too low during the win-

ter sea-son, the battery may

be frozen.



Do not start the engine when

the battery is frozen. Try to

warm it up first.



If the battery is not securely

installed, the battery case and

electrolytes could be damaged

by vibration. To prevent the

battery acid from contacting

the terminals, apply grease

around the battery terminals

and connections.

CAUTION

M46-EU,AU-07.indd 24

2012-01-18 오후 6:39:55

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands