Kioti CS2610 Manual Download

Page: 17 / 170

safetY precautions

11. if the front of the tractor tends to

rise up when heavy implements

are attached to the three point

hitch, weights should be installed

on the tractor. do not operate the

tractor with a light front end.

T66O112a

using the proper adaptor parts,

attach the chain to the tractor

draw-bar support or other speci-

fied anchor location. Provide only

enough slack in the chain to per-

mit turning. see your dealer for a

chain with a strength rating equal

to, or greater than the gross

weight of the towed machine.

12. always use the proper ballast

weight on your tractor when us-

ing rear implements.

13. Watch front and rear to avoid

obstacles at row ends, near trees

and around other obstructions.

T66O113a

M46-EU,AU-01.indd 7

2012-03-09 오전 11:15:53

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands