Kioti CS2610 Manual Download Page 100

Page: 100 / 170

cS2610

This tractor is equipped with the

remote control valve of the double

acting type. However, this valve can

also be used in the single acting type

hydraulic cylinder.
1. connect one end of the hydraulic

port to the single acting cylinder as

shown in the figure. The hydraulic

pressure is properly supplied to the

cylinder. However, when the hydrau-

lic pressure is released, the cylinder

is contracted only if there is outer

force, such as potential energy.

SINGlE.ACTING.AND.DOUblE.ACTING.CylINDER

(1) Single Acting cylinder

(A) External load

H11O585A

(1) Double Acting cylinder

H11O586A

2. To contract the cylinder, operate

the lever to the opposite position of

the expansion. Then, the hydraulic

fluid is supplied from the hydraulic

pump to the hydraulic port which

is not connected, and the pressure

rises as the port is blocked. How-

ever, this pressure is released as

the relief valve opens.

3. When the cylinder is contracted,

the hydraulic fluid returned from

the cylinder is drained to the trans-

mission through the draining circuit

as the operating lever is operated

to the opposite direction from the

expansion position.



.It. is. recommended.to. use. the.

double.acting.cylinder.instead.

of.the.single.acting.cylinder.if.

the.implement.will.be.operated.

frequently. and. continuously..

If.using.the.single.acting.cyl-

inder. too. frequently. or. for. an.

extended. period.of. time,. the.

hydraulic. fluid. can. be. over-

heated,. resulting. in. deteriora-

tion.of.the.hydraulic.parts’.du-

rability.as.the.main.relief.valve.

opens.at.cylinder.contraction.

ImPORTANT

M46-EU,AU-05.indd 24

2012-01-18 오후 6:38:36

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands