Kioti CS2610 Manual Download Page 117

Page: 117 / 170

3-POINT HITcH IMPLEMENT OPERATION

4. fast dump
The fast dump function is activated

when the joystick lever is pushed

one position further to the right

from the dump position.

5. down & roll back
The boom can be lowered and the

bucket can scoop up by operat-

ing the joystick lever to the front

left position (10 o’clock position).

However, the operation time may

not be shortened much since the

boom is lowered first and then the

bucket is rolled back due to unbal-

anced hydraulic pressure in the

hydraulic circuit.

6. down & dump
The boom can be lowered and the

bucket can dump by operating the

joystick lever to the front right posi-

tion (2 o’clock position). However,

these two operations may not be

performed simultaneously due to

unbalanced hydraulic pressure in

the hydraulic circuit.

7. Up & roll back
The boom can be lifted and the

bucket can scoop up by operating

the joystick lever to the rear left

position (7 o’clock position). How-

ever, these two operations may not

be performed simultaneously due

to unbalanced hydraulic pressure

in the hydraulic circuit.

8. Up & dump
The boom can be lifted and the

bucket can dump by operating the

joystick lever to the rear right posi-

tion (5 o’clock position). However,

the operation time is may not short-

ened much since the bucket dumps

first and then the boom is lifted due

to the unbalanced hydraulic pres-

sure in the hydraulic circuit.

9. Locking/unlocking joystick
Pressing the joystick lock lever in

locks the joystick while pulling it

outward unlocks the joystick as

shown in the figure.



Do not leave the tractor with the

boom "Off" the ground in any

circumstances. If it is neces-

sary, lock the joystick.



When the joystick lever is not

in use, lock it since the imple-

ment can fall down if the lever

is operated accidently.

WARNINg



If the boom or bucket is not

operating, properly, lower the

bucket onto the ground, stop

the engine, and relieve all hy-

draulic pressure. Then, check

all the hydraulic connections

and connect them again.



Before connecting or disconnect-

ing the hydraulic hose coupling

from the loader, lower the boom

onto the ground, stop the en-

gine, and move the joystick lever

front and back, left and right for

several times to remove residual

pressure in the hydraulic hose.

IMPORTANT

M46-EU,AU-06.indd 15

2012-01-18 오후 6:39:15

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands