Kioti CS2610 Manual Download Page 78

Page: 78 / 170

cS2610

For detailed information, refer to

“maintenance interval” in chapter 7.

PRE-OPERATION

CHECk.ITEm



Walk around inspection.



check the engine oil level.



check the transmission oil level



check the coolant level.



clean the grill and radiator screen.



Check the air cleaner filter.



check the brake pedal.



check all dash gauges and indicators.



check head lights, tail lights, and

all working lights.



check accessible wiring harness

for any damage.



check the seat belt and

ROPS

for

damage.



check all danger and warning labels.



check fuel level.



check all danger and warning decals.



visually check tire inflation and

wheel bolt tightening.

It is a good practice to know the con-

dition of your tractor before you start

it. you should do a routine check be-

fore each use.



Stop.the.tractor.on.level.ground,.

stop.the.engine,.and.apply.the.

parking.brake.before.checking.

or.repairing.it.

. Refer. to. “Daily. inspection”. in.

the. section. “Service”. for. fuel.

replenishment.



Read. information. titled. as.

“Danger”,. “Warning”,. and.

“Caution”. thoroughly. for. safe.

operation.

CAUTION

M46-EU,AU-05.indd 2

2012-01-18 오후 6:38:15

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands