Kioti CS2610 Manual Download Page 127

Page: 127 / 170

maintenance

M46O706A

(1) oil Dipstick

(a) upper limit

(B) lower limit

1. Park the machine on a flat surface,

lower the implement and shut

"off" engine.

2. Depress the brake pedals and ap-

ply the parking brake.

3. set all shift levers into the neutral

position.

4. stop the engine.

(1) gauge (2) oil filler plug

(a) oil level is acceptable within range

ChECkING TRANsMIssION flUID lEVEl (D)

5. pull out the oil dipstick, clean it,

and then insert it into its original

position. then, pull it out again and

check if the oil level is within the

specified range.

6. if the oil level is too low, add some

new oil so that the level is within

the allowable range. (refer to

"replacing transmission fluid and

filter" in the chapter "Service")



If oil level is low, do not run en-

gine.



Never add the oil over the up

per limit.

IMPORTANT

M46O705A

M46-EU,AU-07.indd 9

2012-01-18 오후 6:39:36

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands