Kioti CS2610 Manual Download Page 73

Page: 73 / 170

desCrIpTION OF OperATING sysTeM

Always maintain the proper tire inflation pressure. Make sure the tire pressure does not exceed the pressure recom

mended in the manual.

INFlATION PRESSuRE



Keep the front tire pressure to maximum if maximum load is applied to the loader or front weight.



If tires with a different size from the ones already in use are installed, contact the

KIOTI

dealer for the front/rear

wheel speed ratio. Improper front/rear wheel speed ratio can result in excessive wear of the tires.

NOTE

CS2610

Tire sizes

Inflation pressure

Front

Farm

Turf

18 x 8.5 - 8 r3

0.6~1.4 kg/cm

, 60~140 Kpa, 8.7~20.3 psi

INd

18 x 8.5 - 8 r4

0.6~1.4 kg/cm

, 60~140 Kpa, 8.7~20.3 psi

rear

Farm

Turf

26 x 12.00 - 12 r3

0.8~1.4 kg/cm

, 80~140 Kpa, 11.6~20.3 psi

INd

26 x 12.00 - 12 r4

0.8~1.4 kg/cm

, 80~140 Kpa, 11.6~20.3 psi

※

INd… for Industrial.

M46-EU,AU-04.indd 29

2012-01-19 오후 1:48:56

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands