Kioti CS2610 Manual Download Page 109

Page: 109 / 170

3-POINT HITcH IMPLEMENT OPERATION

(1) Top Link

(2) Pin

(3) Retainer Pin

(4) Top Link Hook

1. Install the top link to the desired

position, and install the pin and re-

tainer pin.

2. Fix Top link with fixed nut after ad

justing top link.

M46O603A

ADjUsTMENT Of TOP LINK



stop the engine and lower the

attachment to the ground prior

to disconnecting the lift rod

from the lower link. Check that

the attachment has proper

support and that there’s pres-

sure remaining in the hydrau-

lic system to remove the lift

rod holding the pin. To elimi-

nate the remaining pressure,

move the hydraulic adjusting

lever back and forth several

times.

WARNINg



When there is no implement at-

tached, fix the lower link to the

check link (LH/RH) so that it does

not contact with the rear wheel.



Secure the top link to the stor-

age hook.

NOTE

M46O604A

ADjUsTMENT Of sTABILIzER

(1) check Link

(2) Turnbuckle

1. Adjust the check link control hori-

zontal sway of the implement. It is

also used to set the implement on

the back of the tractor in center.

2. To adjust the check link, pull out

the pin and adjust it until the de-

sired transverse moving distance

is obtained.

3. Fit the pin to the fixed hole for nor

mal operation and long hole (mov-

ing) for draft work.

M46-EU,AU-06.indd 7

2012-01-18 오후 6:39:05

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands