Kioti CS2610 Manual Download Page 59

Page: 59 / 170

desCrIpTION OF OperATING sysTeM

P.T.O INDICATOR (IF

EQuIPPED)

M46O416A

M46O415A

4wD ENGAGED INDICATOR (IF

EQuIPPED)

This indicator shows the p.T.O en-

gagement condition. when the p.T.O

is engaged, this indicator comes on.

when the p.T.O clutch is disengaged,

this indicator goes off.



Set the P.T.O switch to the

“OFF” position in order to

start the engine.

CAuTION

This comes on to indicate 4wd en-

gagement.



The durability of the axle can

be deteriorated if only one

brake pedal is depressed

while the 4wD is activated.

CAuTION

CRuISE lAMP (OPTIONAl)

1. Operating condition
Turn on the cruise switch during

driving. Then, the cruise lamp

comes on.

2. deactivation condition
when pressing the brake pedal,

turning off the cruise switch, the

cruise lamp goes off.

M46O451A

M46-EU,AU-04.indd 15

2012-01-19 오후 1:48:35

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands