Kioti CS2610 Manual Download Page 40

Page: 40 / 170

Cs2610

General specifications

external Dimensions

※

these dimensions are measured with the standard tires installed to the roPs model tractor.

M46O301A

※

: overall length including weights and folded roPs

: overall length excluding weights

: overall height with folded roPs

overall height with raised roPs

: Front wheel tread E

: rear wheel tread

item

cs2610

1. overall length (a1)

2,518 (99.13)

2. overall length (a2)

2,791 (109.88)

3. overall width (B)

1,180 (46.46)

4. overall height (C1)

1,899 (74.76)

5. overall height (C2)

1,517 (59.72)

6. Wheel base (d)

1,400 (55.12)

7. tread (E1)

940 (37.01)

8. tread (E2)

850 (33.46)

9. min. ground clearance (F)

183 (7.20)

mm (in.)

M46-EU,AU-03.indd 2

2012-01-18 오후 6:34:18

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands