Kioti CS2610 Manual Download Page 68

Page: 68 / 170

Cs2610

(1) seat Adjustment Lever

To adjust the seat position, pull the

lever (1) to left under the front of the

seat, slide the seat to the desired po-

sition, and then release the lever.

Make sure that the seat is firmly fixed

by moving it gently after adjustment.

SEAT ADJuSTMENT

SEAT SlIDING



Do not put a hand between the

seat and the slides when ad-

justing the seat position. You

can get injured unexpectedly.

CAuTION

M46O436A

(1) seat belt

SEAT bElT

The seat belt is self-retracting type.

Make sure to fasten the seat belt be-

fore driving.



Always fasten the seat belt when

the tractor has ROPS properly.

Otherwise, never wear the seat

belt.



Make sure that the seat belt is

not twisted. It cannot work prop-

erly, leading to a dangerous situ-

ation.

wARNING

M46O437A



The seat is equipped with a

safety device that stops the

engine when the driver's seat

is not occupied.

IMPORTANT

M46-EU,AU-04.indd 24

2012-01-19 오후 1:48:49

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands