Kioti CS2610 Manual Download Page 22

Page: 22 / 170

cs2610

in order to service your tractor you must

park it on a flat level surface, set the

parking brake, place the gear shift lever

in neutral and stop the engine.
1. do not smoke while working around

the battery or when refueling your

tractor. Keep all sparks and flames

away from the battery and fuel

tank. The battery presents an ex

plosive hazard because it vents off

hydrogen and oxygen gas, espe

cially when recharging.

safety Precautions during servicing

T66O124a

2. allow the tractor time to cool "off"

before servicing any part that may

have become hot while the tractor

is running.

3. You must always stop the engine be-

fore refueling the tractor. avoid over-

filling the tractor or spilling the fuel.

4. Before jump starting a dead bat-

tery, read and follow all of the in-

structions.

5. It is recommended to keep a first

aid kit and fire extinguisher handy

at all times.

T66O125a

6. do not remove the radiator cap

while the coolant is hot. When

cool, slowly rotate the cap to the

first stop and allow sufficient time

for excess pressure to escape.

after all the pressure is released

remove the cap completely. if your

tractor is equipped with a coolant

recovery tank, add coolant there

rather than to the radiator.

T66O126a

M46-EU,AU-01.indd 12

2012-03-09 오전 11:15:59

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands