Kioti CS2610 Manual Download Page 91

Page: 91 / 170

opERATIoN

3. Align it to the groove and pull the

set pin to release it.

4. Fix the

ROPS

with the grip bolt.

M46O511A

(1) chocks

(2) parking Brake lever

PARkING

1. This tractor is not equipped with a

separate parking brake. However

uses the brake pedals instead.

2. pull the parking brake lever (2) up

with the brake pedals depressed

fully to engage the pedals with the

latch. If the braking force is insuf-

ficient, depress the pedals more

firmly.

3. Before leaving the tractor after

parking it, make sure to stop the

p.T.o lower the implement onto the

ground, and stop the engine.

4. If it is necessary to leave the tractor

with the engine running, put all the

shift levers in the neutral position

and apply the parking brake firmly.

5. When parking the tractor on a

slope, stop the engine with the

parking brake applied and engage

the low speed gear. Also, put the

shuttle shift lever into the forward

driving position on an uphill and

into the reverse driving position on

a downhill.

(1) Grip Bolt

(2) Set pin

M46O507A

M46-EU,AU-05.indd 15

2012-01-18 오후 6:38:29

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands