Kioti CS2610 Manual Download Page 69

Page: 69 / 170

desCrIpTION OF OperATING sysTeM



be extra careful not to let any

part of your body under the

tractor or an implement when

lowering an implement.

wARNING

M46O438A

HYDRAulIC SYSTEM

POSITION CONTROl lEvER

(1) position Control Lever

(2) Lower Link

(A) Lowering

(b) Lifting

The position control lever is to oper-

ate the hydraulic lift arm to lift and

lower a 3-point hitch implement.
To lower an implement, move the

lever forward. To raise an implement,

move the lever backward.
The position control lever is automat-

ically returned to its neutral position

when the lift arm reaches its upper

limit position.



when lifting and lowering the

lift arm, make sure to place

the position control lever to

the neutral position in order to

stop the lift arm at the desired

position.

IMPORTANT



Make sure that there is no one

around before lowering an imple-

ment.

WARNING

M46-EU,AU-04.indd 25

2012-01-19 오후 1:48:50

Summary of Contents for CS2610











































































































































































Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands

Kioti CS2610, Manual

Search results

Summary of Contents for CS2610

Reviews:

Related manuals for CS2610

Brands by name

Popular brands