manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 47 / 221

Share
Download
Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 47

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 47 / 221

 

Strict confidential 

 

B19 (800 upper) 

TD-SCDMA 

B39 (1900+) 

Data rates: 
• Downlink: Up to 2.8 Mbps 
• Uplink: Up to 2.2 Mbps 
 
Spreading rate: 
• Downlink: 1.28 Mcps 

GSM 
GPRS 
EDGE 
3GPP Release 99 

None 

N/A 

 
Compared to the MC7304 MiniPCIe card, the MC7430 supports more 3G and 4G bands. This 
MiniPCIe  card  is  then  suitable  in  urban  areas  for  instance  where  4G  or  3G  coverage 
excellent. 

1.5.2.3.1

 

LTE - Americas Mini PCI Express card – MC7354 

The next 4G Mini PCI Express card is dedicated to the American market. 
The reference is Sierra Wireless MC7354. 
This module is already PTCRB and CDG2 approved. 
It is also FCC and IC certified: 

 

FCC ID: N7NMC7355 

 

IC ID: 2417C-MC7355 

 
The bands and data rate supported by the module are the following: 
 

Technology 

Band 

Data rate 

LTE 
3GPP Release 9 

Band 2 (1900MHz) 
Band 4 (1700/2100MHz) 
Band 5 (850MHz) 
Band 13 (700MHz) 
Band 17 (700MHz) 
Band 25 (1900MHz) 

Category 3 

 

Downlink: 

o

 

100Mbps (20MHz BW) 

o

 

50Mbps (10MHz BW) 

 

Uplink: 

o

 

50Mbps (20MHz BW) 

o

 

25Mbps (10MHz BW) 

CDMA 
EVDO release 0 
EVDO release A 

BC0 (800MHz) 
BC1 (1900MHz) 
BC10 (800MHz) 

CDMA IS-856 (1xEV-DO Release A) 

 

Up to 3.1 Mbps forward channel 

 

Up to 1.8 Mbps reverse channel 

CDMA IS-2000 

 

Up to 153 kbps, simultaneous forward 
and reverse channel 

Circuit-switched data bearers up to 14.4 kbps 

UMTS 

Band 1 (2100MHz) 

HSPA+ rates: 

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments