manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 189 / 221

Share
Download
Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 189

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 189 / 221

 

Strict confidential 

 

If antenna diversity is required, or additional LoRa modules are required, then the installer 
has  to  add  the  missing  modules  inside  the  enclosure  and  mount  the  required  N-SMB 
adapters  on  the  bottom  side  of  the  enclosure.  8  x  M16  blind  stops  are  available  for  that 
purpose (see §4.4). 
In  order, to  facilitate  the  installation,  KERLINK  recommends  the  following  allocation  of the 
M16 blind stops for the additional N-SMB connectors: 
 

 

Figure 137 : Recommended allocation of the N connectors – Standard casing 

 

Note:

  the  bottom  side  of  the  enclosure  does  not  include  any  label  or  any  serigraphy  to 

differentiate the N connectors. This is because of the full modularity of the Wirnet iBTS. We 
strongly  recommend  to  the  installer  following  KERLINK  recommendations  regarding  the 
placement of the connectors to facilitate the installation. The installer must ensure that the 
right N connector is connected to the right SMB connector of the LoRa module and therefore 
to the right antenna! 
 
In its default configuration, the compact casing features only one N-SMB adapters used as RF 
interfaces for the LoRa antenna: 
 

GPS antenna 

LTE antenna 

LoRa antenna 

WAN 

LoRa 

Module #1 

LoRa 

Module #2 

LoRa 

Module #3 

LoRa 

Module #4 

RF1 

connector 

RF2 

connector 

GNSS 

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments