7
Take whatever steps are necessary to get rid of any dirt
and debris. Get rid of as much water as possible by
giving the gutters time to drain and by drying out with
cloths.
8
Once the cab gutters are dry, re-secure the gutter
blanking plates and refit the floor plate.
9
Start the engine and crowd the shovel to lower the
machine to the ground.
6 - 4
Body and Framework (cont'd)
Cleaning Cab Interior
-
for interval see Service Schedule
Because the machine body base is of solid steel construction
special provision is made for cleaning out the cab. The cab
floor profile incorporates two gutters, one on each side. At
the rear end of each gutter is a blanking plate
A
which is
secured by two bolts.
1
Lower the loader arm to its lowest position with a shovel
installed.
2
Operate the Loader Arm/Shovel control lever as if to tip
the shovel for unloading. This action will raise the front of
the machine off the ground.
3
Stop the engine and remove the starter key.
4
If necessary, remove the floor plate in front of the
operator's seat by unscrewing the four bolts securing it to
the chassis.
5
Loosen the blanking plates
A
from the ends of the
chassis gutters - slacken off one bolt and the plate will
swing away.
Note:
The illustration shows the left gutter blanking plate. A
similar plate is fitted to the right side gutter.
6
Hose out the machine floor taking care not to get water
into the electrical circuits.
Note:
Hose pressure should not be too high.
Checking Seat Belt Condition and Security
-
for interval
see Service Schedule
!
!
WARNING
Replace the seat belt with a new one if it is damaged, if
the fabric is worn, or if the machine has been in an
accident. Fit a new seat belt every three years regardless
of condition.
2-3-1-8
When checking the seat belt, look for signs of fraying and
stretching. Make sure the stitching is not loose or damaged.
Make sure the buckle assembly is working correctly and not
damaged. Fit a new seat belt every three years.
Make sure the belt mounting bolts are undamaged, correctly
fitted and tightened.
Section 3
Routine Maintenance
9803/8500
Section 3
6 - 4
Issue 1
A
A
174161
Summary of Contents for ROBOT 150
