10 - 8
Hydrostatic Pump
from machine no. 676355
Dismantling and Assembly
Following a complete rebuild of this pump it is necessary for
it to be set up on a dynamic test jig. Because of this it is
recommended that no dismantling work is carried out beyond
that covered in the following pages.
Shaft Seal
Removal and Replacement
1
Remove circlip
1
.
Note:
It may be necessary to press shaft
2
into the body
against spring force before the circlip can be removed.
When the circlip is removed, seal carrier
3
will move out
approximately 6 mm (0.25 in.) due to spring force.
2
Lightly tap the end of shaft
2
with a rubber mallet and
remove seal carrier
3
.
Note:
After the seal carrier has been removed, the shaft
2
and bearing assembly
4
are free in the body. Under no
circumstances should the shaft be removed as this could
cause loss of alignment of the pump internals
necessitating a total strip and rebuild. Such a procedure
is outside the scope of this Service Manual.
3
Remove O-ring
5
from seal carrier
3
. Discard the O-ring.
4
Using a suitable press, press out lip seal
6
from the seal
carrier. Discard the lip seal.
5
Inspect seal carrier
3
for damage, and the sealing area
on shaft
2
for signs of rust, wear or contamination. Polish
the sealing area on the shaft if necessary.
6
Coat the outside diameter of new lip seal
6
with suitable
sealant. Press the lip seal into the shaft bearing side of
seal carrier
3
, ensuring that the seal lip faces the shaft
bearing. Take care not to damage the lip seal.
7
Lubricate the inside diameter of lip seal
6
with petroleum
jelly.
8
Install new O-ring
5
onto seal carrier
3
and lubricate with
petroleum jelly.
9
Wrap the splined end of shaft
2
with thin plastic to
prevent damage to the lip seal during installation.
10
Slide seal carrier
3
over shaft
2
and press into position in
the pump body recess.
11
Holding inward pressure against shaft
2
, refit circlip
1
to
secure the assembly.
Section E
Hydraulics
9803/8500
Section E
*10 - 8
Issue 4*
Pumps
S244910
2
4
6
5
3
1
*
Summary of Contents for ROBOT 150
