![background image](http://html1.mh-extra.com/html/jai/vis-cam-system/vis-cam-system_installation-manual_3223355104.webp)
VIS-CAM Systems
92
Appendix H
12
Appendix H: ENcamera Firmware Upgrade Guide
Note: Completely review before attempting firmware upgrades
12.1
Prior to firmware upgrade:
1
Check JAI support site for the newest version of the ENsetup software.
www.jai.com
or there is a link
located in the help section of the first ENsetup menu after login.
2
Check your firmware file date to be sure you are using the correct zip file or go to support site and
download newest firmware version.
3
Be sure you have a good ethernet connection before you begin.
DO NOT ATTEMPT MULTIPLE CAMERA UPGRADES. UPGRADE
ONE
CAMERA AT A TIME
.
4
The software will allow you to try it but do not. It could result in cameras being returned to JAI
for repair.
12.2
To begin upgrade:
1
Save the firmware zip file on the pc you will use for the upgrade.
2
Go to ENsetup properties page. Left click on the camera to be upgraded. The IP address of the camera
will be highlighted and the camera properties will be displayed on the right.
3
Go to section 8 – Version and verify which firmware you are running.
4
Right click on the camera to be updated and click Advanced Settings then click Update Firmware in
Camera on the menu.
5
The Firmware update dialog box appears – click Firmware Update button.
NOTE: DO NOT CHECK FORCE UPDATE OR AUTOMATICALLY REBOOT boxes unless instructed to by JAI.
6
Select firmware file box appears. Locate the zip file you saved on your pc and click open.
12.3
Firmware upgrade begins:
1
The software will do a bit check of all firmware files loaded in the camera. Then update all newer files
from zip to camera.
2
If the software encounters a file in the camera newer than the zip file, a dialog box will appear asking if
you are sure you want to load this older file. Click yes and the older file will overwrite the existing file.
Click no and the upgrade will continue without loading older file.
Note: When falling back to an older firmware, be sure of the file dates. The older firmware could
cause some functionality issues if not the exact same file as the one used prior.
3
When the upgrade has concluded, the Firmware Update dialog box will reappear.
4
Click the “X” in the right hand corner to exit. A box will appear asking if you would like to reboot the
camera. (See SECTION 4 below) Click ok and the camera will reboot and a red X will appear over the IP
address of the camera being updated.
5
After camera reboots about 1 minute, click on the cameras IP address and verify in the properties section
8 that the new file dates appear there.
6
The camera is now firmware updated and should be running normally. Verify proper operation of camera.
Summary of Contents for VIS-CAM System
