1
www.observint.com
ALI-CD1080P-1720P_CQ
10/21/14
What’s in the box
•
Camera assembly
•
Mounting hardware
•
Torx® L- wrench
•
Drill template
•
This instruction guide
Tools you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for voltage and wattage requirements.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Video and power extension cable
•
CCTV video setup monitor (optional)
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Monitor impedance
: Set the monitor impedance switch to 75 Ω.
•
Power supply
:
Camera drop cable
: The camera drop cable includes two connectors:
—
Video BNC connector
: For transmission of the video signal across a coax (75 Ω) extension cable.
—
Power connector:
When applying Vdc power, observe the power polarity. See the picture above
for connector polarity configuration.
1.
Using the drill template provided with your camera, mark the location of the screws that anchor the
base plate to the mounting surface. If you are routing the drop cable through base, also mark the
position of the hole for the drop cable.
2.
Drill holes for the screws that anchor the base to the ceiling. The mounting hardware provided is
appropriate for most surfaces. However, depending on the surface materials, more appropriate
fasteners may be required.
3.
Drill a 3/4” hole for the drop cable, if necessary. The drop cable can be routed through the mounting
surface, or through a cable channel in the mounting plate.
4.
Route camera video and power extension cables between camera location and the monitoring
device (monitor, DVR, etc.).
5.
Remove the mounting plate from the camera assembly
u
Loosen the clip plate captive screw with the L-wrench provided.
u
v
Clip plate
Enclosure
v
Slide the clip plate out as shown in the photo above.
Separate the mounting base from the enclosure.
ALI-CD1720P, ALI-CD1080P HD-TVI
Outdoor Infrared Turret Camera
Quick Installation Guide
The ALIBI™ ALI-CD1080P and ALI-CD1720P cameras feature a 1/3” CMOS image sensor that delivers high-
definition video resolution over RG59 coax or any standard analog CCTV cabling up to 1600 ft. These HD
video camera is ideal for security applications that require a high level of detail, such as facial recognition or
license plate identification.
Features
•
CMOS image sensor
•
HD-TVI technology produces 1280x720 (720p, ALI-CD1720P) or 1920x1080 (1080p, ALI-CD1080P)
HD video for sharp, detailed images
•
3.6 mm wide angle (77°) lens captures images over large areas
•
HD-TVI technology transmits zero latency HD video resolution over coax cabling
•
Built-in IR with 24 LEDs enables the camera to see up to 65’ in the dark
•
Smart IR technology reduces over-exposure of the IR LEDs at the center of the image
•
True day/night (ICR) captures sharp, clear images in low light and at night
•
-40 °F ~ 140 °F (ALI-CD1720P) extreme temperature operating range
•
IP66 weather-rated housing
Mounting
plate
IR array
Lens
Camera
module
Enclosure
Clip plate
ALI-CD1720P and ALI-CD1080P cameras
Power
Connector
HD-TVI video BNC
Connector
ALI-CD1720P Camera drop cable connectors
Power
Connector
RS-485 leads
HD-TVI video BNC
Connector
CVBS video BNC
Connector
ALI-CD1080P camera drop cable connectors
