Immergas Hercules Condensing 26 2 E Manual Download Page 63

Page: 63 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

List of accessories and optionals.

Radio timer-thermostat (wireless)

code 3.014439

Super Comando Amico Remoto remote control

code 3.016577

GSM telephone control kit

code 3.017182

External Probe

code 3.014083

Comando Amico Remoto remote control

code 3.011236

Solar panels coupling kit

code 3.019998

Digital weekly timer-thermostat

code 3.014438

Telephone control

code 3.013305

Clock kit for recirculation

code 3.015431

DHW recirculation kit (including pump)

code 3.020001

Cut-off cocks kit

code 3.4297

Cut-off cocks with filter kit

code 3.015854

Polyphosphate dispenser kit

code 3.019999

Water network cut-off kit

code 3.020000

Direct low temperature safety thermostat kit

code 3.019869

Condensate drain pump kit

code 3.020002

List of dedicated accessories only for HERCULES Condensing

2nd and 3rd additional high temperature zones kit

code 3.018838

2nd and 3rd additional low temperature zones kit

code 3.020003

2nd additional high temperature zone kit

code 3.018837

2nd additional low temperature zone kit

code 3.018836

Configurable relay interface kit

code 3.015350

List of dedicated accessories only for HERCULES Condensing ABT 32 2 I

3rd additional low temperature zone kit

code 3.018839

The boiler is prepared for coupling to the DIM (Multi-system Distribution Manifold), available in 5 recess or wall-hung kits.

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands