Immergas Hercules Condensing 26 2 E Manual Download Page 67

Page: 67 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

Flue evacuation takes place correctly.

Clean/restore the correct functionality of the flue extraction elements,

checking lengths and any obstructions.

Clean/restore the correct functionality of the condensation module

checking that there are no combustion impurities deposited on the heat

exchanger (soot, oxidations, etc..).

Yes

If the anomaly persists, replace the P.C.B.

ERROR 04

Contacts resistance block

The overheating safety thermostat functions regularly.

Check the wiring and cleanliness of the electric connection, the continuity

of the thermostat contact and replace if necessary.

Yes

The connector and relative wiring between gas valve and P.C.B.

are OK.

Restore the electric connection/replace the wiring.

Yes

Replace the gas valve. If the anomaly persists, replace the P.C.B.

ERROR 05

Flow probe anomaly

The wiring between the flow probe and the board (connector X9

terminals 10-11) is OK.

Restore the electric connection/replace the wiring.

Yes

Replace the NTC flow probe. If the anomaly persists, replace the P.C.B.

ERROR 10

Insufficient system pressure

The boiler manometer displays a pressure exceeding 0.8 bar.

Restore the correct pressure by acting on the system filling valve.

N.B.: in this case it is always advisable to ensure that there are no leaks

in the central heating plant and check the correct factory-set value of the

expansion vessel.

Yes

The wiring between the absolute pressure switch and the board is OK. No

Restore the electric connection/replace the wiring.

Yes

Check/replace the system pressure switch. If the anomaly persists, replace the P.C.B.

ERROR 12

Storage tank probe anomaly

The boiler prevents functioning in DHW mode but can function in CH mode.

The wiring between the storage tank probe and the board (connector

X9 terminals 6-7) is OK.

Restore the electric connection/replace the wiring.

Yes

Replace the storage tank NTC probe. If the anomaly persists, replace the P.C.B.

ERROR 15

The boiler could display the 06 error

Wiring configuration error

N.B.: This board can be used for instant type boilers (VICTRIX Superior kW)

or with storage tank (VICTRIX ZEUS Superior kW ). The board automatically

recognises the type of boiler by means of the relative wiring of the P.C.B.

The board is configured as boiler with storage tank.

(presence of the jumper between clamps 6-7 of the connector X7).

For the HERCULES Condensing boiler check the PRESENCE of the

connection jumper between clamps 6-7 of the connector X7.

Yes

Replace the P.C.B.

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands