Immergas Hercules Condensing 26 2 E Manual Download Page 42

Page: 42 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Electric circuit.

Fase riscaldamento.

Operating with room thermostat.

By pressing the main button ( ) boiler activation is ena-

bled.

By using button (A) to select functioning in (Winter) func-

tioning is enabled in CH mode.

On closure of the room thermostat contact (S20) and if the

system pressure switch contact (S5) is closed (pressure detected

in the primary circuit higher than minimum value) the inte-

grated P.C.B. powers the pump (M1) by means of relay K2,

after which, by diversion of the K4 relay contact it powers the

motor (M) of the 3-way valve (M30). This functions until the

end run switch "1" opens when the CH position is reached.

This leads to the power supply of relay K1 positioned on the

pump relay board (A10) and the consequent power supply of

the CH pump (M2).

If the temperature detected by the NTC flow probe (B1) is

below the setting made on the control panel using the CH

temperature selector, the integrated P.C.B. powers the fan

(M20) and manages the speed.

With the consent of the safety thermostat (E4) and the flue

safety thermostat (E6) and the fan (M20) reaching the "validate

ignition" speed, the integrated P.C.B. allows to start the igni-

tion cycle by controlling, first the ignition electrodes (E1) by

means of the K7 igniter relay and then the K3 request relay,

both the coils of the gas valve (Y1).

The ignition of the burner is detected by the integrated P.C.B.

by means of the ionisation electrode (E2).

Operation with Remote Control.

In the case of connection to the CAR or Super CAR remote

control, the boiler automatically detects the device and the

(

) symbol appears on the display.

If the conditions detected by the Remote Control (CAR or

Super CAR) request ignition in CH mode (SUM/WINT selector

of the CAR in WINTER pos or Super CAR button working

(Winter), CH temperature adjustment higher than that detected

by the CH flow probe (B1), requested by the programmer clock,

room temperature adjustment higher than that detected)), the

integrated P.C.B. manages the burner ignition cycle as previ-

ously described.

N.B.

: By pressing the main switch ( ) and taking the boiler

into Stand-by, the CAR will show the "CON" connection error

symbol and the "ERR>CM" error will appear on the Super

CAR. The remote control is kept powered without losing the

memorised programs.

N.B.

: Every time switch off occurs when temperature is

reached, the integrated P.C.B. blocks burner functioning in

CH mode for a period of time equal to that set with board

parameters (see integrated P.C.B. functioning).

est

t w

ate

tra

l h

tin

SAFETY EXTRA-LOW

VOLTAGE CIRCUIT

LOGIC

-CONTR

OLS MICR

OPR

OCESSOR

Super CAR remote

control (Optional)

SIGNAL

STATE

IMG BUS

link

Storage tank

function

jumper

RELAY BOARD (Optional)

Link for

VIRGILIO palmtop

Microprocessor

programming connector

CH ON

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands