Immergas Hercules Condensing 26 2 E Manual Download Page 20

Page: 20 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Functioning with mixed systems (as per standard for HERCULES Condensing ABT, optional for

HERCULES Condensing)
(configuration with Low Temperature Kit).

The coupling to a mixed system divided into two zones envi-

sions the installation of the "low temperature kit" inside the

casing.

The assembly of this kit leads to the use of a three-way mixing

valve (7), a zone management board (21) (see "Zones digital

control unit" functioning) prepared for control of the valve and

the pump (10), a system by-pass (13) and one-way valve (9)

to be inserted into the system return pipe.

Thanks to this system, the boiler can serve two zones operat-

ing at differentiated temperatures; a high temperature zone

(example radiators) and a low temperature zone (example floor

radiating panels).

high temperature” zone (zone 1 already standard).

This portion of circuit is envisioned to operate at an ideal

temperature for radiator plants, fan coils etc.

It is served by the standard pump and its temperature is ad-

justed by acting on the boiler control panel.

“low temperature” zone (zone 2).

This portion of circuit is envisioned to operate with floor

panel systems.

It is served by a pump (10) which, via a motorised 3-way

mixing valve (7), introduces water into the system at constant

temperature.

To allow this, the 3-way valve (7) is controlled by a P.C.B.

(21) that varies the position depending on the pre-selected

temperature (from 25°C to 50°C).

This setting is made on the boiler control panel.

The temperature of the flow water is obtained by mixing the

high temperature circuit flow water and the low temperature

STORAGE TANK

COILS

FLOW

STORAGE TANK

COILS

RETURN

circuit return water in variable quantities according to neces-

sity, (see hydraulic diagram).

The control of the correct mixing is entrusted to an NTC probe

(12) connected to the zones control unit (21).

RA1

MA1

RB1

MB1

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands