Immergas Hercules Condensing 26 2 E Manual Download Page 48

Page: 48 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Outputs.

It allows the connection of electronic devices, e.g. Immergas zones digital control unit.

IMG BUS connection

(optional)

It is a signal (BUS) that shows boiler temperature, functioning in DHW and Ch mode,

the alarm codes that have intervened and the temperature detected by any external probe

on the remote control display.

Comando Amico Remoto

remote control (CAR)

(optional) (see CAR functioning)

It is a relay that allows to power the motor (M) of the electric 3-way valve (M30). It is

excited with a central heating request and remains in stand-by with a domestic hot water

request.

Three-way valve relay

(K4)

It is a signal (BUS) that shows boiler temperature, functioning in DHW and Ch mode,

the alarm codes that have intervened and the temperature detected by any external probe

on the remote control display.

Super CAR

(optional)

It is a unipolar relay that is excited when burner ignition is necessary. The electric spark takes

place at the ends of the ignition electrodes positioned on the burner, due to its contact.

Igniter relay

(K7)

It is a unipolar relay that allows to power the gas valve coils when the boiler must be

ignited.

Gas valve relay

(K3)

It is a unipolar relay for boiler pump control (M1) that is excited when its functioning

is requested.

Boiler pump relay

(K2)

It is a positive square wave signal with variable ON-OFF relationship (duty-cycle) that

controls the fan.

Allows to vary the air flow rate to the Venturi pipe and therefore the gas pressure to the

burner.

Fan

It is a 24 V DC signal that indicates the power supply of the main coils of the gas valve.

Gas valve power supply

(Y1)

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands