Immergas Hercules Condensing 26 2 E Manual Download Page 40

Page: 40 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Allows the integrated P.C.B. to detect the temperature of the pri-

mary circuit flow water.

Its breakage (signalled by relative anomaly) blocks burner functioning

both in central heating and domestic hot water modes.

It is positioned at the outlet of the main heat exchanger.

Flow probe

(B1)

NTC probe

10 kΩ 25 °C

It allows the integrated P.C.B. to detect the temperature of the

exiting domestic hot water.

Its breakage (signalled by relative anomaly) allows the boiler to

continue working in the central heating mode.

It is inserted into a hole made on the outside wall of the storage

tank to which it is fixed.

Domestic hot water probe

(B2)

NTC probe

10 kΩ 25 °C

Detects the external temperature and allows the integrated

P.C.B. to vary the flow temperature depending on the external

temperature.

External probe

(B4) (optional)

PTC probe

1 kΩ 25 °C

Low voltage circuit.

Safety devices and controls.

When the pressure of the boiler circuit is below 0.3 bar it determines

burner switch-off.

System pressure switch

(S5)

Contact in

Shut-off

It is a resistance that simulates the presence of the system return

probe. It must always be present.

Return probe resistance

(R9)

Factor

2,2 kΩ 1/4 W

Allows long distance control of the generator (SUM/WIN selector

switch, temperature adjustment and indication, alarms display, reset,

etc.) and acts as weekly timer thermostat.

If the CAR is installed the pre-existing X40 jumper must be

eliminated.

Comando Amico Remoto

remote control

(CAR) (optional)

See Comando

Amico Remoto

remote control

functioning

(CAR)

Allows long distance control of the generator (SUM/WIN fun-

ctioning, temperature adjustment and indication, programs and

parameters setting alarms display, reset, etc.) and acts as weekly timer

thermostat.

If the Super CAR is installed the pre-existing X40 jumper must

be eliminated.

Super CAR

(optional)

See Super CAR

functioning

It is mounted on the front inside the boiler in the top right part.

In the case of assembly of the additional zones management kits,

the board controls all electric devices connected to it (e.g. motorised

mixing valves, pumps, NTC probes, safety thermostats etc).

N.B.: in the HERCULES Condensing ABT model, the zones
digital control unit is supplied as per standard.

Zones digital control unit

IMG BUS connection

(optional)

See functioning

technical sheet

Zones digital

control unit

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands