Immergas Hercules Condensing 26 2 E Manual Download Page 41

Page: 41 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

Loads.

Enables functioning in CH mode when the room temperature is

below that requested.

If the CAR or Super CAR is installed, the room thermostat must

be disconnected without restoring the pre-existing jumper X40.

Room thermostat (S20)

(external optional)

Contact in

Shut-off

Buttons and selector switches can be used to RESET the boiler, set, modify and memorise

boiler functioning values.

By means of the display and according to the buttons selected it is possible to display the

functioning values and error codes that have intervened on the boiler.

Display board

(A4)

It allows the connection of electronic devices, e.g. Immergas zones digital control unit.

IMG BUS outlet

When the safety temperature is exceeded (100 °C) remove the

power supply to the main coils of the gas valve.

It is positioned on the flow pipe at the outlet of the primary heat

exchanger.

Safety thermostat

(E4)

Klixon thermostat

with normally

closed contact

Guarantees the flow of air in the sealed chamber and the escape of combustion prod-

ucts.

It is powered by the integrated P.C.B.

Fan

(M20)

When the flue safety temperature is exceeded (110 °C) remove the

power supply to the main coils of the gas valve.

It is positioned on the condensation module.

Flue safety thermostat

(E6)

Klixon thermostat

with normally

closed contact

It is powered (24 V DC) by the integrated P.C.B. when burner ignition is necessary.

Allows the passage of gas to the burner.

Gas valve (Y1)

(main coils)

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands