Immergas Hercules Condensing 26 2 E Manual Download Page 46

Page: 46 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Inputs.

It sends SUMMER/WINTER selector switch, DHW and CH temperature adjustment

and CH request signals to the board (time, room temperature, error codes, etc...).

Comando Amico Remoto

remote control (CAR)

(optional) (see CAR functioning)

When the pressure of the primary circuit is lower than 0.3 bar

remove the power supply to the K3 relay, thus preventing burner

ignition.

System pressure switch

(S5)

Open =

No pressure

Closed =

Pressure OK

It allows the connection of electronic devices, e.g. Immergas zones digital control unit.

IMG BUS connection

(optional)

It sends the board a signal that allows ignition or boiler stand-by.

Button

It sends a signal to the board that allows boiler functioning in Summer

( ) or Winter ( ) mode.

Button "A"

It sends the board a signal that allows to activate or deactivate the DHW priority func-

tion.

Button "B"

It sends the board a signal that allows to release the integrated P.C.B. after the intervention

of an anomaly or boiler block, signalled with the relative "ERR xx"" error code (see errors

and anomalies list).

In the P.C.B. programming mode it allows to exit the configuration menu.

Button "C"

It sends the P.C.B. a signal that allows to enter the configuration menu and to confirm

the adjustments made.

Button "D"

It is a signal that indicates that the flame has been detected.

It allows the integrated P.C.B. to increase the fan speed after having

limited it during the ignition phase.

Flame detection

(E2)

Flame signal =

6 ÷ 15 microA

It sends the board the signals of the various functioning state, programming setting,

information and reset buttons as well as DHW and CH temperature adjustment signals

and CH request (time, room temperature, error codes, etc...).

Using the Super CAR it is possible to indifferently vary some settings from the boiler con-

trol panel and from the Super CAR control panel, such as: selection of Summer Winter,

DHW comfort status, DHW set point.

Super CAR

(optional)

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands