Immergas Hercules Condensing 26 2 E Manual Download Page 43

Page: 43 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

Circuito elettrico.

Electric circuit.

Operation.

By pressing the main button ( ) boiler activation is enabled,

which is enabled for functioning in the DHW phase.

If the temperature detected by the DHW NTC probe (B2),

positioned on the storage tank, is lower than the setting made

on the control panel (or on the CAR or Super CAR if mounted)

and if the contact of the system pressure switch (S5) is closed

(pressure detected in the primary circuit higher than minimum

value), the integrated P.C.B uses the K2 relay to power the

boiler pump (M1), after which by diversion of the K4 relay

contact it powers the motor (M) of the 3-way valve (M30).

This functions until the end run switch "2" opens when the

DHW position is reached.

Successively the integrated P.C.B. powers the fan (M20) and

manages the speed.

With the consent of the safety thermostat (E4) and the flue

safety thermostat (E6) and the fan (M20) reaching the "validate

ignition" speed, the integrated P.C.B. allows to start the igni-

tion cycle by controlling, first the ignition electrodes (E1) by

means of the K7 igniter relay and then the K3 request relay,

both the coils of the gas valve (Y1).

The ignition of the burner is detected by the integrated P.C.B.

by means of the ionisation electrode (E2).

est

t w

ate

tra

l h

tin

LOGIC

-CONTR

OLS MICR

OPR

OCESSOR

SAFETY EXTRA-LOW

VOLTAGE CIRCUIT

Super CAR remote

control (Optional)

SIGNAL

STATE

IMG BUS

link

RELAY BOARD (Optional)

Link for

VIRGILIO palmtop

Microprocessor

programming connector

Storage tank

function

jumper

CH ON

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands