Immergas Hercules Condensing 26 2 E Manual Download

Page: 54 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

1st

Level

Button

2nd Level

Button

3rd Level

Button

Description

M1 (INFO)





P11

(SOFTWARE)





Displays the management software version of the circuit board installed

in the boiler

P12

(HEAT.TIME)

Displays the total operating hours of the boiler

P13

(IGNIT.NR)

Displays the number of burner ignitions

P14

(OUTSIDET.)

(with optionall

external probe

present)

(NO EXT.P.)

(without optional

external probe

present)





P14/A

(CURRENT)

Displays the current external temperature (if external probe is present

Optional)

P14/B

(OUT T.MIN)

Displays the minimum external temperature recorded (if external probe is

present Optional)

P14/C

(OUT T.MAX)

Displays the maximum external temperature recorded (if external probe is

present Optional)

RESET

selection



By pressing button“D” the MIN and MAX temperatures measured are

reset

P15

(DHW FLOW)





No display for this model

P17

(FANSPEED)

Displays the speed in instantaneous revs of the fan

P18

(PUMPSPEED)

The value displayed does not affect this model

P19

(FAILURE)

Displays the last 5 events that have caused the boiler to shutdown

The sequential number from 1 to 5 along with the relative error code

By pressing button “D” repeatedly, it is possible to display opeating times

and the number of ignitions where the anomaly took place

Information menu M1 (INFO).

This menu contains the

various information relative to boiler operations:

1st

Level

Button

2nd Level

Button

3rd Level

Button

4th Level

Button

Description

M3 (P

ERS. MENU)





P31

(DISPLAY)





(LIGHT)

AUTO

(Default)

selection



The display lights up when the burner is

on and when the controls are accessed.

It remains on for 5 seconds after the last

operation performed

(LIGHT) ON

The display is always lit

(LIGHT) OFF

The display only lights up when the

controls are accessed and remains on for 5

seconds after the last operation performed

P32

(DISP.

DATA)





P32/A

(DISP.DESC.)





P32/A.1

(CH.TEMP.)

(Default)

selection



The indicator displays the output

temperature from the primary heat

exchanger

P32/A.2

(OUTSIDET.)

The indicator displays the current external

temperature (with external probe Optional)

P32/B

(LANGUAGE)





ITALIAN

(Default)

All descriptions are given in Italian

(ALPHANUM)

All descriptions are given in Alphanumeric

mode

P33

(EMER-

GENCY)





OFF

(EMERG.)

selection



By activating this function in winter mode,

the room heating function can be activated

even if the Remote Control or TA are out

of order

(EMERG.)

RESET

(RESET

ALL)

selection



By pressing button “D” the customisations

made are reset, restoring the values set in

the factory

Customisations menu M3 (PERS.MENU).

AThis menu

contains all operating options that can be customised. (The

first entry of the various options that appears within the para-

meter is that selected by default).

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands