Immergas Hercules Condensing 26 2 E Manual Download Page 64

Page: 64 / 72

STHCkW ed 0409

HERCULES Condensing Export

Technical Documentation

Before every intervention:

Check that the gas, water and electricity are correctly connected

to the boiler, according to that indicated in the data plate and

the instruction manual.

Also make sure that:

- the gas valve and boiler parameters are correctly adjusted;

- all devices outside the boiler function and are appropriately

adjusted;

- the external and internal fuses are integral.

Before maintenance interventions or replacement of compo-

nents, remove the electric power supply upstream from the

appliance.

For correct use of the troubleshooting table, on intervention it

is recommended to press the Reset button, switch the boiler off

and remove voltage from the appliance for at least 5 seconds.

This is to allow the boiler to start a new ignition cycle.

Ignition cycle

Ricerca guasti HERCULES Condensing.

CENTRAL HEATING MODE

Press the main button ( ), and then press button A (WINTER).

Turn the central heating selector switch to maximum to prevent domestic

hot water functioning by pressing button B.

N.B.: wait for the completion of any DHW request if the temperature in

the storage tank is below 20°C.

The boiler pump

starts.

N.B.: the display

must show CH

Check the presence of the TA jumper on clamps

40-41 of the P.C.B.

N.B.: the jumper must not be present when

external devices are installed such as TA, CAR,

clock programmer, etc...

Check the effective request from any external

devices (TA/CAR programmer clock).

See

error section 31.

If present zones digital control unit (as standard

for HERCULES Condensing ABT)

See section F

See section B

Yes

The 3-way valve goes

into the CH posi-

tion.

See section C

Yes

The zone pump

starts

See section G

DOMESTIC HOT WATER MODE

Press the main button ( ), and then press button A (SUMMER).
Turn the DHW selector switch to maximum and open the cock

N.B.: the display must show DHW

The boiler pump starts.

See section B

Sì

The 3-way valve goes into the DHW

position.

See section C

Apply voltage to the boiler.
The display lights up.

See section A

Yes

The error 05 appears on the display

Yes

See error section 05

The error 06 appears on the display

Yes

See error section 15

The error 10 appears on the display

Yes

See error section 10

The error 12 appears on the display

Yes

See error section 12

The error 23 appears on the display

Yes

See error section 23

The error 24 appears on the display

Yes

See error section 24

The error 32 appears on the display

Yes

See error section 32

The error 33 appears on the display

Yes

See error section 33

The error 34 appears on the display

Yes

See error section 34-a

The error 35 appears on the display

Yes

See error section 35-a

The error 37 appears on the display

Yes

See error section 37

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands