Immergas Hercules Condensing 26 2 E Manual Download Page 47

Page: 47 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

It is a clean contact switch that sends a signal (in low voltage) to

the board enabling functioning in the CH mode when the room

temperature is lower than that requested.

Room thermostat

(S20)

(external optional)

Open = Central

heating OFF

Closed = Central

heating ON

It is a contact which, on opening, allows the board to identify and

display any flue safety thermostat intervention (E6) with an "ERR

03" error code.

Flue safety thermostat

(E6)

Open = Function-

ing OFF

Closed = Func-

tioning ON

It is a resistance that can be varied proportionally to the external

temperature.

It allows the integrated P.C.B. to vary the system flow temperature

depending on the external temperature.

External probe (B4)

(optional)

PTC probe

1 kΩ 25 °C

It is a resistance that can be varied in an inversely proportional

manner to the temperature of the primary circuit flow water.

It is also used as a limit thermostat on the flow (90 °C).

Flow probe

(B1)

NTC probe

10 kΩ 25 °C

It is a resistance that can be varied in an inversely proportional

manner to the temperature of the water contained in the storage

tank.

Domestic hot water probe

(B2)

NTC probe

10 kΩ 25 °C

It is a contact which, on opening, allows the board to identify and

display any flue safety thermostat intervention (E4) with an "ERR

02" error code.

Safety thermostat

(E4)

Open = Function-

ing OFF

Closed = Func-

tioning ON

It is a square wave signal detected with a Hall effect sensor inserted into the fan. It allows

the integrated P.C.B. to measure the speed and correct it if it does not comply with the

requested value.

Fan speed

It is a resistance that simulates the presence of the system return

probe. It must always be present.

Return probe resistance

(R9)

Factor

2,2 kΩ 1/4 W

Summary of Contents for Hercules Condensing 26 2 E









































































Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands

Immergas Hercules Condensing 26 2 E, Manual

Search results

Summary of Contents for Hercules Condensing 26 2 E

Reviews:

Related manuals for Hercules Condensing 26 2 E

Brands by name

Popular brands