imagistics im3510 Operation Manual Download Page 15

Page: 15 / 128

1-5

PART NAMES AND FUNCTIONS

Interior

* For replacement and installation of cartridges, refer to the Getting Started Guide.

Duplex module side cover

Open when a misfeed has occurred in the duplex
module.

Side cover latch

Push up to open the side cover when a misfeed has
occurred in the main unit.

Fusing unit

Lift up to open the side cover when a misfeed has
occurred in the main unit.

CAUTION

The fusing unit is hot. Take care in removing misfed
paper.

Developer cartridge*

This cartridge contains developer and must be
removed and replaced by a new cartridge when
indicated on the operation panel.

Toner cartridge (drum/toner cartridge)

The toner cartridge must be replaced when indicated
on the operation panel.

Photoconductive drum

Images are formed on the photoconductive drum.

NOTE

Do not touch or damage the photoconductive drum.

Cartridge lock lever

When replacing the drum, toner or developer
cartridge, turn down this lever and pull it out.

Summary of Contents for im3510

































































































































Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands

imagistics im3510, Operation Manual

Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands