imagistics im3510 Operation Manual Download Page 100

Page: 100 / 128

5-24

SADDLE STITCH FINISHER

Misfeed in the saddle stitch finisher

When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below.

Unlatch the saddle stitch finisher and slide
it away from the printer.

Remove the misfed paper from the main
unit.

After removing the misfed
paper, open and close
the duplex module to
reset the jam indicator.
(step 1 or 5 on page 4-4)

If misfed paper is not found in step 1, open
the top cover.

While pulling and turning roller rotating
knob B, remove the misfed paper.

If the misfed paper is
released by turning roller
rotating knob B, remove
it taking care not to tear
the paper.

Close the top cover.

If saddle stitch was selected, open the front
cover.

Remove the misfed paper from the stapler
compiler.

Be careful not to tear the
misfed paper during
removal.

Open the saddle stitch section cover.

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

Roller rotating
knob B

Summary of Contents for im3510

































































































































Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands

imagistics im3510, Operation Manual

Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands