imagistics im3510 Operation Manual Download Page 90

Page: 90 / 128

5-14

Misfeed in the finisher

When a misfeed occurs in the finisher, remove the misfed paper following the procedure below.

Remove the misfed paper from the output
area.

Be careful not to tear the
misfed paper during
removal.

Open the finisher top cover.

Top cover

Move the tab in the
direction of the arrow as
shown in the illustration to
open the top cover.

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.
After removing the paper,
press down on the top
cover to close it.

Open the finisher compiler.

Release the latch to open
the finisher compiler.

Raise the paper guide and remove the
misfed paper.

Paper
guide

Do not remove paper
from the stapler compiler.

Close the finisher compiler.

FINISHER

Summary of Contents for im3510

































































































































Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands

imagistics im3510, Operation Manual

Search results

Summary of Contents for im3510

Reviews:

Related manuals for im3510

Brands by name

Popular brands