manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 65 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 65

 Chapter 3. Components overview 

47

Rear view

The following sections detail the LEDs, controls and connectors for the power 
supply and controller at the rear of the storage subsystem.

Power supply

Figure 3-13 shows the LEDs, controls and connectors on the power supply.

Figure 3-13   DS400 power supply LEDs, controls and connectors

򐂰

AC power connector - Connect the power cord to this connector. 

򐂰

AC power on/off switch - Use this switch to turn the power supply on and off. 

򐂰

Power OK LED (green) - When this LED is lit, it indicates that the power 
supply is turned on. 

򐂰

Fault LED (amber) - When this LED is lit, there is a fault with either the power 
supply or a fan.

Table 3-8   Power supply LEDs

Power supply problem Indicator

Action

Green Power Supply Power LED is off.

Verify that the power cord is plugged in and that the 
storage subsystem power is on.

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments