manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 570 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 570

552

 

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 9-154   Select boot LUN 

8. The target and the LUN is added to the boot device list. Press 

ESC

 to return 

to 

Adapter Settings

.

Figure 9-155   Defined boot targets and LUNs 

9. Press 

ESC

 to leave 

Adapter Settings

 and return to 

Configuration Settings

.

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments