IBM TotalStorage DS300 Best Practices Manual Download Page 303

Page: 303 / 680

Chapter 7. TotalStorage DS300 installation

285

Figure 7-90 Hardware update completed

When you check now the Windows device manager, you will find a new SCSI
adapter device

QLogic iSCSI Adapter

in the

SCSI and RAID controllers

section and one unknown device less in the

Other devices

section.

Figure 7-91 Windows device manager with unknown devices (network controller)

Summary of Contents for TotalStorage DS300








































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TotalStorage DS300

Reviews:

IBM TotalStorage DS300, Best Practices Manual, Page: 303 / 680

Search results

Summary of Contents for TotalStorage DS300

Reviews: