manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 542 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 542

524

 

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 9-113   Selected device is not a disk device 

e. Select from the list of LUNs the LUN from which the server will boot. The 

logical drive 

WOLGA-BOOT

 was as first logical drive assigned to the initiators. 

The DS400 will present the configured logical drives in that order to the 
host as they where assigned to the initiator. Select the 

LUN 0

 end press 

Enter

.

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments